Weld Mount 1.25" Tall Stainless Panel Stud w/0.62" Base & #8 x 32 Thread - Qty. 15 Weld Mount 1.25" Tall Stainless Panel Stud w/0.62" Base & #8 x 32 Thread - Qty. 15
Online
$21.89 for Each
Retail $26.27
Mfr PN: 83220
Stock: 33
1.25" Tall Stainless Stud w/#8 x 32 Thread

Our Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite surfaces. The base plate is 0.62" in diameter with a 1.25" tall stud. Tensile strength is 300 lbs. and shear strength is 375 lbs. Maximum torque load is 45 inch/lbs.
Online
$21.89 for Each
Retail $26.27
Mfr PN: 83220
Stock: 33

GROCO Spanner Wrench/Deck Plate Key GROCO Spanner Wrench/Deck Plate Key
Online
$23.77 for Each
Retail $26.75
Mfr PN: SW-2531
Stock: 32

Spanner Wrench/Deck Plate Key 

Features:

  • Cast bronze with stainless steel pins to fit 1/4" and 5/16" holes. 
  • Opens to service deck plates or strainer caps with key holes up to 7" apart. 
  • Hangs conveniently near the strainer(s) location. 
  •  C83600 bronze
Online
$23.77 for Each
Retail $26.75
Mfr PN: SW-2531
Stock: 32

Weld Mount No Slide Metal/Composite Bonder Weld Mount No Slide Metal/Composite Bonder
Online
$32.90 for Each
Retail $41.13
Mfr PN: 8040
Stock: 25
No Slide Metal/Composite Bonder

Revolutionary Metal Bonder will hold heavy parts at application without sliding either on a vertical or overhead surface. AT-8040 will hold 3,500lbs in 40 minutes. No Welding, Drilling or Tapping.

Weld Mount AT-8040 is a solvent free, VOC Compliant, two part methacrylate-based, structural adhesive formulated to bond metals for use in severe environments. It will also bond engineered thermo- and thermosetting plastics, composites to metals or various substrate combinations. It has excellent adhesion to as received metal surfaces including aluminum, stainless steel, galvanized steel, and plated steels. AT-8040 forms a tough, high strength bonds usually with minimal surface preparation developing handling strength in 12 minutes and a functional cure within 45 minutes. Ultimate strength exceeds 3500 psi of tensile shear strength on aluminum with remarkable impact and peel strengths. AT-8040 will hold all Weld Mount parts on a vertical or overhead surface without sagging when properly used.

Features:
  • Revolutionary Adhesive
  • Parts Stay Where Placed Without Sliding
  • For Use Overhead and on Vertical Surfaces
  • No Need for Fixtures
Online
$32.90 for Each
Retail $41.13
Mfr PN: 8040
Stock: 25

Weld Mount AT-850 Square Mixing Tip f/AT-8040 & AT850 - 4" - Case of 10 Weld Mount AT-850 Square Mixing Tip f/AT-8040 & AT850 - 4" - Case of 10
Online
$15.13 for Each
Retail $18.91
Mfr PN: 80850
Stock: 24
AT-850 Square Mixing Tip f/AT-8040 - 4" - Case of 10

Weld Mount's AT-850 tip is for use only with the AT-8040. It's unique design eliminates any possibility of the cartridge plugging up as the entry is separated.

Features:
  • Square Mixing Tip
  • 4" Long
  • Case of 10
Online
$15.13 for Each
Retail $18.91
Mfr PN: 80850
Stock: 24

Weld Mount Retail Wire Tie Kit w/AT-8040 Adhesive Weld Mount Retail Wire Tie Kit w/AT-8040 Adhesive
Online
$37.68 for Each
Retail $45.22
Mfr PN: 1050
Stock: 21
Retail Wire Tie Kit
CAN NOT SHIP AIR, UPS GROUND ONLY

The AT-1050 kit contains one manual mix tube of AT-8040 adhesive and 25 pc. AT-5 white wire tie mount. Just enough parts for a small wiring job and ideal introduction to Weld Mount.

The AT-1050 Kit contains:
  • AT-8040 Adhesive
  • (25) Pieces AT-5 White Tie Mount
  • (1) Plastic Mixing Sheet
  • (2) Mixing Sticks
  • Complete step-by-step instructions
Online
$37.68 for Each
Retail $45.22
Mfr PN: 1050
Stock: 21

Weld Mount AT-2010 Acrylic Adhesive Weld Mount AT-2010 Acrylic Adhesive
Online
$34.28 for Each
Retail $41.13
Mfr PN: 2010
Stock: 20
Acrylic Adhesive
CAN NOT SHIP AIR,UPS GROUND ONLY

AT-2010 is our biggest seller and is a unique adhesive. It has high viscosity and will hold smaller parts without sagging. AT-2010 cures in 5 - 6 minutes, has a 4 minute working time and develops working strength in 15 -20 minutes. This makes AT-2010 the ideal adhesive for applications which require an immediate high strength bond. AT-2010 has a 6 month shelf life when stored at 72 degrees. We recommend that where ever possible this adhesive be refrigerated. Packaged in a 50ml cartridge and can be mixed by hand or by using our AT-300 gun and mixing tips. The 50ml cartridge will bond 150 - 200 parts.

** AT 850 Mixing Tips sku 56273 required **
Online
$34.28 for Each
Retail $41.13
Mfr PN: 2010
Stock: 20

Weld Mount AT-4020 Acrylic Adhesive Weld Mount AT-4020 Acrylic Adhesive
Online
$33.34 for Each
Retail $41.13
Mfr PN: 4020
Stock: 19
Acrylic Adhesive
CAN NOT SHIP AIR,UPS GROUND ONLY

AT-4020 is a specially formulated adhesive for holding all our parts with little or no sagging in vertical or overhead applications. Cures in 10 - 12 minutes and has working strength within 40 minutes. AT-4020 is recommended for composite and plastic bonding applications and not for bonding to metal substrates. Unlike other 2 part acrylic adhesives AT-4020 has a one year shelf life when stored at 72 degrees but is best refrigerated when ever possible. It is packaged in a 50ml cartridge and can be mixed by hand or by using our AT-300 gun and mixing tips. The 50ml cartridge will bond 150 - 200 parts.
Online
$33.34 for Each
Retail $41.13
Mfr PN: 4020
Stock: 19

Sea-Dog Add-A-Snap - White - 1-1/2" Sea-Dog Add-A-Snap - White - 1-1/2"
Online
$4.58 for Each
Retail $4.99
Mfr PN: 299201W-1
Stock: 19

Add-A-Snap - White - 1-1/2" 

For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.

WarningWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Online
$4.58 for Each
Retail $4.99
Mfr PN: 299201W-1
Stock: 19

Weld Mount .75" Tall Stainless Panel Stud w/0.62" Base & #8 x 32 Thread - Qty. 15 Weld Mount .75" Tall Stainless Panel Stud w/0.62" Base & #8 x 32 Thread - Qty. 15
Online
$17.32 for Each
Retail $20.78
Mfr PN: 83212
Stock: 19
.75" Tall Stainless Stud w/#8 x 32 Thread

Our Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite surfaces. The base plate is 0.62" in diameter with a .75" tall stud. Tensile strength is 300 lbs. and shear strength is 375 lbs. Maximum torque load is 45 inch/lbs.
Online
$17.32 for Each
Retail $20.78
Mfr PN: 83212
Stock: 19

Weld Mount 1.5" Tall Stainless Panel Stud w/0.62" Base & #8 x 32 Threads - Qty. 15 Weld Mount 1.5" Tall Stainless Panel Stud w/0.62" Base & #8 x 32 Threads - Qty. 15
Online
$22.57 for Each
Retail $27.84
Mfr PN: 83224
Stock: 18
1.5" Tall Stainless Stud w/#8 x 32 Thread

Our Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite surfaces. The base plate is 0.62" in diameter with a 1.5" tall stud. Tensile strength is 300 lbs. and shear strength is 375 lbs. Maximum torque load is 45 inch/lbs.
Online
$22.57 for Each
Retail $27.84
Mfr PN: 83224
Stock: 18

Weld Mount 1" Tall Stainless Stud w/1/4" x 20 Threads - Qty. 10 Weld Mount 1" Tall Stainless Stud w/1/4" x 20 Threads - Qty. 10
Online
$26.44 for Each
Retail $30.85
Mfr PN: 142016
Stock: 17
1" Tall Stainless Stud w/1/4" x 20 Thread

Mounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile strength and 650 lbs. in shear. All studs have 1/4" x 20 threads. Use for hanging panels, through deck mounts and many other uses.
Online
$26.44 for Each
Retail $30.85
Mfr PN: 142016
Stock: 17

Weld Mount 1" Tall Stainless Panel Stud w/0.62" Base & #8 x 32 Thread - Qty. 15 Weld Mount 1" Tall Stainless Panel Stud w/0.62" Base & #8 x 32 Thread - Qty. 15
Online
$19.70 for Each
Retail $24.31
Mfr PN: 83216
Stock: 13
1" Tall Stainless Stud w/#8 x 32 Thread

Our Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite surfaces. The base plate is 0.62" in diameter with a 1" tall stud. Tensile strength is 300 lbs. and shear strength is 375 lbs. Maximum torque load is 45 inch/lbs.
Online
$19.70 for Each
Retail $24.31
Mfr PN: 83216
Stock: 13

Davis Deluxe Rigging Knife Davis Deluxe Rigging Knife
Online
$18.74 for Each
Retail $24.99
Mfr PN: 1551
Stock: 12
Deluxe Rigging Knife

Made entirely of top quality stainless steel with dura-edged blades. Telo Rigging knives are tools that yachtsmen will be proud to own, yet are affordable.

Deluxe Rigging Kinfe comes with a marlin spike, shackle key, and screwdriver.
Online
$18.74 for Each
Retail $24.99
Mfr PN: 1551
Stock: 12

Sea-Dog Add-A-Snap - Black - 2-1/2" Sea-Dog Add-A-Snap - Black - 2-1/2"
Online
$4.84 for Each
Retail $5.49
Mfr PN: 299202B-1
Stock: 12

Add-A-Snap - Black - 2-1/2" 

For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.

WarningWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Online
$4.84 for Each
Retail $5.49
Mfr PN: 299202B-1
Stock: 12

Sea-Dog Add-A-Snap - White - 4" Sea-Dog Add-A-Snap - White - 4"
Online
$5.18 for Each
Retail $5.99
Mfr PN: 299204W-1
Stock: 12

Add-A-Snap - White - 4" 

For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.

Online
$5.18 for Each
Retail $5.99
Mfr PN: 299204W-1
Stock: 12

Weld Mount AT-5 Large White Nylon Wire Tie Mount - Qty. 30 Weld Mount AT-5 Large White Nylon Wire Tie Mount - Qty. 30
Online
$17.84 for Each
Retail $21.40
Mfr PN: 805
Stock: 12
White Nylon Wire Tie Mount

The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!
Online
$17.84 for Each
Retail $21.40
Mfr PN: 805
Stock: 12

Weld Mount AT-5 Large White Nylon Wire Tie Mount - Qty. 50 Weld Mount AT-5 Large White Nylon Wire Tie Mount - Qty. 50
Online
$33.28 for Each
Retail $38.82
Mfr PN: 805950
Stock: 10
White Nylon Wire Tie Mount

The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!
Online
$33.28 for Each
Retail $38.82
Mfr PN: 805950
Stock: 10

Weld Mount AT-5B Large Black Nylon Wire Tie Mount - Qty. 100 Weld Mount AT-5B Large Black Nylon Wire Tie Mount - Qty. 100
Online
$51.96 for Each
Retail $64.96
Mfr PN: 805900B
Stock: 10
Black Nylon Wire Tie Mount

The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!
Online
$51.96 for Each
Retail $64.96
Mfr PN: 805900B
Stock: 10

Sea-Dog Stainless Steel Bottle Opener w/Brushed Finish Sea-Dog Stainless Steel Bottle Opener w/Brushed Finish
Online
$15.89 for Each
Retail $19.95
Mfr PN: 588450-1
Stock: 10

Stainless Steel Bottle Opener with Brushed Finish 

Corrosion resistant investment cast 316 stainless steel bottle opener wall mounts with two #6 FH fasteners (not included).

WarningWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Online
$15.89 for Each
Retail $19.95
Mfr PN: 588450-1
Stock: 10

Weld Mount AT-300 Adhesive Dispensing Gun f/AT-2010 & AT-4020 Weld Mount AT-300 Adhesive Dispensing Gun f/AT-2010 & AT-4020
Online
$69.65 for Each
Retail $85.91
Mfr PN: 80300
Stock: 9
Adhesive Dispensing Gun

The AT-300 Adhesive dispensing gun has a 1:1 plunger for use with AT-2010 and AT-4020 50ml cartridges. When using AT-6030 adhesive it requires AT-12 (10 to 1 plunger). Replacement plungers are also available.
Online
$69.65 for Each
Retail $85.91
Mfr PN: 80300
Stock: 9

Weld Mount AT-5 Large White Nylon Wire Tie Mount - Qty. 100 Weld Mount AT-5 Large White Nylon Wire Tie Mount - Qty. 100
Online
$55.68 for Each
Retail $64.96
Mfr PN: 805900
Stock: 8
White Nylon Wire Tie Mount

The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!
Online
$55.68 for Each
Retail $64.96
Mfr PN: 805900
Stock: 8

Sea-Dog Add-A-Snap - Black - 4" Sea-Dog Add-A-Snap - Black - 4"
Online
$5.18 for Each
Retail $5.99
Mfr PN: 299204B-01
Stock: 8

Add-A-Snap - Black - 4" 

For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.

WarningWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Online
$5.18 for Each
Retail $5.99
Mfr PN: 299204B-01
Stock: 8

Weld Mount 1.25" Tall Stainless Stud w/#10 x 24 Threads - Qty. 10 Weld Mount 1.25" Tall Stainless Stud w/#10 x 24 Threads - Qty. 10
Online
$23.09 for Each
Retail $28.50
Mfr PN: 102420
Stock: 8
1.25" Tall Stainless Stud w/#10 x 24 Thread

Utilize the same base as the 1.4" x 20 studs but with a smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items which require a smaller stud diameter. These studs can be bonded from either surface of the base plate.
Online
$23.09 for Each
Retail $28.50
Mfr PN: 102420
Stock: 8

Weld Mount AT-850 Square Mixing Tip f/AT-8040 - 4" - Case of 50 Weld Mount AT-850 Square Mixing Tip f/AT-8040 - 4" - Case of 50
Online
$70.50 for Each
Retail $89.96
Mfr PN: 8085050
Stock: 8
AT-850 Square Mixing Tip f/AT-8040 - 4" - Case of 50

Weld Mount's AT-850 tip is for use only with the AT-8040. It's unique design eliminates any possibility of the cartridge plugging up as the entry is separated.

Features:
  • Square Mixing Tip
  • 4" Long
  • Case of 50
Online
$70.50 for Each
Retail $89.96
Mfr PN: 8085050
Stock: 8

Weld Mount AT-3 Small White Nylon Wire Tie Mount - Qty. 30 Weld Mount AT-3 Small White Nylon Wire Tie Mount - Qty. 30
Online
$13.94 for Each
Retail $17.67
Mfr PN: 803
Stock: 7
White Nylon Wire Tie Mount

The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.
Online
$13.94 for Each
Retail $17.67
Mfr PN: 803
Stock: 7

Weld Mount AT-3B Small Black Nylon Wire Tie Mount - Qty. 30 Weld Mount AT-3B Small Black Nylon Wire Tie Mount - Qty. 30
Online
$14.32 for Each
Retail $17.67
Mfr PN: 803B
Stock: 7
Black Nylon Wire Tie Mount

The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.
Online
$14.32 for Each
Retail $17.67
Mfr PN: 803B
Stock: 7

Weld Mount Mixing Tips f/Use w/AT-6030,AT-2010, & AT-4020 Weld Mount Mixing Tips f/Use w/AT-6030,AT-2010, & AT-4020
Online
$14.93 for Each
Retail $18.91
Mfr PN: 80650
Stock: 7
Adhesive Mixing Tip For AT-6030

Our AT-650 mixing tip is designed specifically for use with our AT-6030 adhesive. AT-6030 is a 10 to 1 adhesive which requires a mixing tip with more mixing chambers to insure proper mixing before use. These mixing tips minimize waste compared with traditional 6" mixing tips. pkg contains 10 mixing tips.
Online
$14.93 for Each
Retail $18.91
Mfr PN: 80650
Stock: 7

GROCO Thru-Hull Installation Tool GROCO Thru-Hull Installation Tool
Online
$76.66 for Each
Retail $92.00
Mfr PN: THT-530
Stock: 6

Thru-Hull Installation Tool 

Thru Hull Installation Tool

The Concept:

THT-530 makes the installation of standard GROCO thru-hull fittings possible by a single installer.  Slide the thru-hull fitting, flanged end first, over the tool.  (It will stop at the proper step.)  Tie a length of monofilament to the eye and place it into the already-cut hole in the hull of the boat.  Apply caulking to the flange of the fitting, and pull the fitting through the hole and against the hull from inside the boat.  Thread the mono-filament through the locknut or seacock. With the fitting pulled firmly against the hull the locknut or the seacock may be screwed onto the fitting.

THT-530 fits GROCO Thru-hull Fitting Sizes from 1/2" through 3"

Online
$76.66 for Each
Retail $92.00
Mfr PN: THT-530
Stock: 6

Weld Mount 1.5" Tall Stainless Stud w/5/16" x 18 Threads - Qty. 5 Weld Mount 1.5" Tall Stainless Stud w/5/16" x 18 Threads - Qty. 5
Online
$43.45 for Each
Retail $53.59
Mfr PN: 51618245
Stock: 5
1.5" Tall Stainless Stud w/5/16" x 18 Thread

The HS200 stud is designed for heavy load applications such as mounting filters and panels. Thestud is inertial (friction) welded to a 2" base plate creating a very strong part. Manufactured of 304 stainless steel. Tensile strength is approximately 1,200 lbs. and shear strength is 1,500 lbs.
Online
$43.45 for Each
Retail $53.59
Mfr PN: 51618245
Stock: 5

Weld Mount Executive Adhesive & Fastener Kit w/AT-8040 Adhesive Weld Mount Executive Adhesive & Fastener Kit w/AT-8040 Adhesive
Online
$231.58 for Each
Retail $289.49
Mfr PN: 1001003
Stock: 5
Executive Adhesive & Fastener Kit w/AT-8040 Adhesive

This Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For The Full Service Yard Or Custom Builder. The Kit Contains 1 Tube Of Our AT-8040 No Slide Multi Bonder Acrylic Adhesive Which Will Bond To Almost All Surfaces Except Low Energy Plastic Or Rubber. AT-8040 Will Hold Even Our Heaviest Parts on a Vertical or Overhead Surface Without Fixturing. The Adhesive Sets in 12 Minutes And Is Heat Resistant To 225°. The Adhesive Should Be Refrigerated and Has A Shelf Life Of 1 year.

The Weld Mount System Eliminates The Need To Drill Into Cored Composites Which Can Result In Hull & Deck Delaminations. No Need To Drill, Tap, or Weld When Used On Metal Surfaces. Great For Mounting Electronics, Wire Runs, Bilge Applications, Water Separators, Battery Switches, Etc.

The AT-1001003 Kit Contains:
  • (1) AT-8040 - No Slide Multi Bonder Acrylic Adhesive
  • <(1) AT-300 - Dispensing Gun
  • (10) AT-850 - 3.5" Mixing Tips For AT-8040 Adhesive
  • (100) AT-5 - Large White Cable Tie Mount
  • (50) AT-3 - Small White Cable Tie Mount
  • (4) AT-113 - Large Footman's Strap
  • (10) PS62-832-16SS - 1.00" Long Panel Stud
  • (4) ST125-1420-16SS - 1.00" Long Stud With 1/4 x 20 Threads 1.25" Base
  • (4) ST125-1420-24SS - 1.50" Long Stud With 1/4 x 20 Threads 1.25" Base
  • (4) ST125-1024-12SS - .75" Long Stud With #10 x 24 Threads 1.25" Base
  • (4) ST125-1024-24SS - 1.50" Long Stud With #10 x 24 Threads 1.25" Base
  • (1) Plano Storage Box 14" x 9" x 2.75"
  • Step By Step Instructions
Online
$231.58 for Each
Retail $289.49
Mfr PN: 1001003
Stock: 5

Weld Mount Executive Fastener Kit - No Adhesive Weld Mount Executive Fastener Kit - No Adhesive
Online
$196.18 for Each
Retail $251.78
Mfr PN: 1001008
Stock: 5
Executive Fastener Kit - No Adhesive

This Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For The Full Service Yard Or Custom Builder. The Kit Does NOT Contain Acrylic Adhesive

The Weld Mount System Eliminates The Need To Drill Into Cored Composites Which Can Result In Hull & Deck Delaminations. No Need To Drill, Tap, or Weld When Used On Metal Surfaces. Great For Mounting Electronics, Wire Runs, Bilge Applications, Water Separators, Battery Switches, Etc.

The AT-1001008 Kit Contains:
  • (1) AT-300 - Dispensing Gun
  • (10) AT-850 - 3.5" Mixing Tips For AT-8040 Adhesive
  • (100) AT-5 - Large White Cable Tie Mount
  • (50) AT-3 - Small White Cable Tie Mount
  • (4) AT-113 - Large Footman's Strap
  • (10) PS62-832-16SS - 1.00" Long Panel Stud
  • (4) ST125-1420-16SS - 1.00" Long Stud With 1/4 x 20 Threads 1.25" Base
  • (4) ST125-1420-24SS - 1.50" Long Stud With 1/4 x 20 Threads 1.25" Base
  • (4) ST125-1024-12SS - .75" Long Stud With #10 x 24 Threads 1.25" Base
  • (4) ST125-1024-24SS - 1.50" Long Stud With #10 x 24 Threads 1.25" Base
  • (1) Plano Storage Box 14" x 9" x 2.75"
  • Step By Step Instructions
Online
$196.18 for Each
Retail $251.78
Mfr PN: 1001008
Stock: 5

Weld Mount AT-5B Large Black Nylon Wire Tie Mount - Qty. 30 Weld Mount AT-5B Large Black Nylon Wire Tie Mount - Qty. 30
Online
$17.34 for Each
Retail $21.40
Mfr PN: 805B
Stock: 5
Black Nylon Wire Tie Mount

The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!
Online
$17.34 for Each
Retail $21.40
Mfr PN: 805B
Stock: 5