10" DuraBlack Double-Skirted Stovepipe Adaptor is used to adapt DuraBlack stovepipe to appliance flue outlets. Outer wall covers appliance flue outlet.
|
10" Duravent DuraChimney II Double-Wall Chimney Pipe Roof Radiation Shield is required at the top of chase enclosure or where the chimney passes through the roof. A Roof Radiation Shield is not required if the chimney is unenclosed in the attic. Four plates (included)make up one shield. Three of the four plates shown.
|
10" - 12" Duravent DuraChimney II Double-Wall Chimney Pipe Spark Arrestor is used on inside of cap. Optional Spark Arrestor may be required.
|
The Diameter Increaser is used to increase the diameter of a vent.special order.
|
12" Duravent DuraChimney II Anchor with Damper Plate is used as a starter section for DuraChimney II products. Bolts directly to the fireplace outlet. Damper section allows the chimney to be closed when the fireplace is not in use. Includes chain and lintel hook.
|
DirectVent Pro Features fully unitized, twist-lock construction in 3á diameters. It can be used in both vertical and horizontal installations. Stainless steel welded seam inner wall, combined with a galvalume welded seam outer wall. Inner and outer are sealed with O-Ring gaskets. Galvalume outer finish. To calculate installed length, subtract 1 1/2á from each length of pipe. CVS is listed to 0á clearance as a double wall vent system for Category II, III, and IV appliances, for flue temperature of up to 400+F for horizontal enclosures, and up to 480+F for vertical enclosures.
|
3" - 4" Type B Gas Vent Attic Insulation Shield is required for installations that pass through an attic to prevent insulation and debris from accumulating near the vent.
|
3" Duravent PelletVent Galvalume 12" Adjustable Length Pipe is used to add length to PelletVent pipe. 12á pipe adds 3á-10á of length when used with rigid sections of pipe.
|
3" Duravent PelletVent Galvalume 45-Degree Elbow offsets obstructions as needed. Elbows swivel 360+ at base. Angle not adjustable.
|
3" to 4" Duravent PelletVent Increaser is used to transition from 3á pipe to a 4á pipe. Not a reducer or stove adaptor.
|
3" Duravent PelletVent Pro Wall Strap is used to support vent pipe or tee sections. Provides 1á clearance.
|
The DuraTech Base Tee is used to connect gas or oil-burning appliances to DuraTech Chimney. No adaptor is needed to connect this to the support box. Tee cap is included. Important: You must maintain an 18" clearance (air space) to combustible materials. DuraTech is a double-wall, all-fuel chimney system for use with wood stoves, fireplaces, furnaces, boilers, ranges, water heaters, or other appliances fueled by wood, oil, coal, or gas, and zero-clearance fireplaces that are factory-built.
|
4" FasNSeal Double-To-Single Wall Adaptor is used to transition from double-wall pipe to single-wall pipe.
|
5" FasNSeal Double-To-Single Wall Adaptor is used to transition from double-wall pipe to single-wall pipe.
|
3" FasNSeal Universal Appliance Adaptor features a built-in mechanical locking band, which allows for quick and simple installations. Meant to be used on appliances and 3" FasNSeal Vent Pipes.
|
4" FasNSeal Universal Appliance Adaptor features a built-in mechanical locking band, which allows for quick and simple installations. Meant to be used on appliances and 4" FasNSeal Vent Pipes.
|
5" FasNSeal Universal Appliance Adaptor features a built-in mechanical locking band, which allows for quick and simple installations. Meant to be used on appliances and 5" FasNSeal Vent Pipes.
|
6" FasNSeal Universal Appliance Adaptor features a built-in mechanical locking band, which allows for quick and simple installations. Meant to be used on appliances and 6" FasNSeal Vent Pipes.
|
This adjustable 0/12 - 6/12 roof flashing is used to weather-proof the penetration of chimney pipe through the roof. Storm collar required.
|
This adjustable 0/12 - 6/12 roof flashing is used to weather-proof the penetration of chimney pipe through the roof. Storm collar required.
|
This elbow offsets obstructions as needed. Elbows angles are now adjustable. Adjustable elbows are manufactured drip-free so creosote travels back to the stove as intended.
|
This chase top flashing encloses the top of a chase while providing a ventilation air passage to the chase. Includes spacer clips.
|
This chimney cap is used to terminate the chimney system and to keep rain and debris out of your flue. Required on all installations. Slides over the previous section of DuraChimney II pipe to allow for chimney height adjustment. Includes a spark arrestor to prevent sparks from jumping out of flue.
|
This storm collar is used to help prevent rain from entering the chase. Use with a flashing and a chimney cap.
|
DuraVent Part Number: 99141
10" Duratech Anchor Plate This item cannot ship to APO/FPO addresses. . M&G DuraVent provides no warranty for the following professional products if such products are not installed by a trained professional installer: DuraTech-+, DuraPlus HTC-+, DuraChimney-+ II, PelletVent Pro-+, DirectVent Pro-+, FasNSeal-+, FasNSeal-+ W2, FasNSeal-+ Flex, and PolyPro-+, and M&G DuraVent's relining products including DuraLiner-+, DuraFlex-+ (SW, Pro, 316, 304), and Ventinox-+. G¬= Any M&G DuraVent product sold by a non-approved website will not be warranted. G¬= Any customer that has bought product from a non-approved website will not be given technical assistance or support from M&G DuraVent. G¬= Any website not compliant with this Internet Sales Policy shall not use M&G DuraVent's trademarked and registered properties, and will be notified to remove them immediately. DuraVent reserves the right to enforce its intellectual property rights against entities not in compliance with this Internet Sales Policy. |
This elbow strap is used to prevent excessive weight on the elbows by supporting the weight of the chimney. Required to be installed between two elbows in offset installations. Multiple elbow straps may be required for offset installations.
|
This finishing collar fits over the female end of the chimney pipe to provide a decorative black finish. Use on chimney pipe that is suspended with the roof support system or on pipe that is passing through a wall thimble.
|
This firestop radiation shield is used in ceiling/floor penetrations to help reduce the chances of a fire. Fits on underside of ceiling and adjusts to cover framing.
|
This 0/12 - 6/12 pitch roof flashing is used to weatherproof the penetration of chimney pipe through the roof. Storm collar required.
|
This storm collar is required with DuraTech flashing to create a weather-proof penetration through the roof deck. Seal inner edge of the collar to the chimney pipe with non-hardening 500-degreeF high temperature sealant.
|
This tee support bracket is used as a wall support for chimney system. Supports up to 30' of DuraTech Chimney. Attaches to chimney pipe. Can be installed above or below the Tee. If installed below the Tee, a short section of pipe is required.
|
This tee with cap is used for through-the-wall installations. Includes removable tee cap for easy chimney cleaning or inspection. Wall straps, a wall thimble, and an adjustable tee support bracket must be installed with the tee as directed.
|
|
|
|
|
Copyright © 1999-2024 BuilderDepot, Inc. Site Designed and Maintained by Inline Internet Systems, Inc. |