10-Conductor In-Line Cable Splice - IP67 Airmar CHIRP transducers are made with cables ending in a bare wire connection. Some sounders have internal terminal blocks to which these bare wires can be connected, but many CHIRP fishfinders and sounders use brand-specific connectors. |
117WR-1 Crows Foot Transducer Wrench
Transducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut.
For use with:
|
117WR-2 Transducer Hull Nut Wrench
A single-handed wrench to tighten the hull nut on 2" bronze and stainless steel housings. You can use wrench 117WR-4 to brace the housing when using this wrench. For use with:
|
117WR-4 Transducer Housing Wrench
A single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the side of the housing to facilitate tightening of the hull nut. For 2" bronze and stainless steel housings (P617V, B617V, SS617V). Use wrench 117WR-2 or 117WR-3 for the hull nut. *Note that this wrench will not fit on the CA500 camera housing. |
164WR-1 Crows Foot Transducer Wrench
Transducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut.
For use with:
|
164WR-2 Transducer Hull Nut Wrench
A single-handed wrench to tighten the hull nut on B164, SS164 and SS264 housings. You can use wrench 164WR-4 to brace the housing when using this wrench. For use with:
|
164WR-3 Double Handle Transducer Wrench
Transducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut.
For use with:
|
175WR-4 Transducer Housing Wrench
A single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the top of the housing to facilitate tightening of the hull nut. Use wrench 164WR-2 or 164WR-3 for the hull nut. For use with:
IMPORTANT: the design of the housing for these transducers changed slightly in June 2012. This wrench is for the newer design and has an internal width of 2-3/4". If you need a wrench for the older designs then use the 164WR-4 instead, with an internal width of 2-7/16". |
60WR-1 Crows Foot Transducer Wrench
Transducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut.
For use with:
|
60WR-2 Transducer Hull Nut Wrench
A single-handed wrench to tighten the hull nut on 2" bronze and stainless steel housings. You can use wrench 60WR-4 to brace the housing when using this wrench. For use with:
|
60WR-3 Double Handle Transducer Wrench
Transducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut.
For use with:
|
60WR-4 Transducer Housing Wrench
A single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the side of the housing to facilitate tightening of the hull nut. Use wrench 60WR-2 or 60WR-3 for the hull nut. For use with:
|
75WR-1 Crows Foot Transducer Wrench
Transducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut.
For use with:
|
75WR-2 Transducer Hull Nut Wrench
A single-handed wrench to tighten the hull nut on bronze and stainless steel housings. You can use wrench 75WR-4 to brace the housing when using this wrench. For use with:
|
75WR-3 Double Handle Transducer Wrench
Transducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut.
For use with:
|
75WR-4 Transducer Housing Wrench
A single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the side of the housing to facilitate tightening of the hull nut. Use wrench 75WR-2 or 75WR-3 for the hull nut. For use with:
|
B175H Bronze Thru Hull 20° Tilt - 1kW Requires Mix and Match Cable Rely on Airmar’s new broadband transducers for your ultimate fishing mission. Whether you’re a commercial fisherman, charter captain, or tournament angler, there’s a new game in town! Chirp transducers enable bottom detection down to 3,000m (10,000’) with 5 to 10 times greater detail and resolution so precise it’s possible to distinguish between individual baitfish, game fish, and underwater structures. One transducer delivers up to 80 kHz of total bandwidth in just one installation, saving customers time and money.
|
B175HW Bronze Thru Hull 0° Tilt - 1kW Get more coverage under the boat with Airmar's new wide beam Chirp product line. Offering a high frequency range of 150-250 kHz and a constant 25° beam width, these transducers are truly broadband at its best. In addition to improving the performance of Chirp-ready echosounders, anglers using the new wide beam transducers will achieve twice the coverage under the boat compared to our current high frequency Chirp transducers Features:
|
B175HW Bronze Thru Hull 12° Tilt - 1kW Requires Mix and Match Cable Get more coverage under the boat with Airmar's new wide beam Chirp product line. Offering a high frequency range of 150-250 kHz and a constant 25° beam width, these transducers are truly broadband at its best. In addition to improving the performance of Chirp-ready echosounders, anglers using the new wide beam transducers will achieve twice the coverage under the boat compared to our current high frequency Chirp transducers Features:
|
B175HW Bronze Thru Hull 20° Tilt - 1kW Requires Mix and Match Cable Get more coverage under the boat with Airmar's new wide beam Chirp product line. Offering a high frequency range of 150-250 kHz and a constant 25° beam width, these transducers are truly broadband at its best. In addition to improving the performance of Chirp-ready echosounders, anglers using the new wide beam transducers will achieve twice the coverage under the boat compared to our current high frequency Chirp transducers Features:
|
B175M Bronze Thru Hull 0° Tilt - 1kW Requires Mix and Match Cable Rely on Airmar’s broadband transducers for your ultimate fishing mission. Whether you’re a commercial fisherman, charter captain, or tournament angler, there’s a new game in town! Chirp transducers enable bottom detection down to 3,000m (10,000’) with 5 to 10 times greater detail and resolution so precise it’s possible to distinguish between individual baitfish, game fish, and underwater structures. One transducer delivers up to 80 kHz of total bandwidth in just one installation, saving customers time and money. Features:
|
B175M Bronze Thru Hull 12° Tilt - 1kW Requires Mix and Match Cable Rely on Airmar’s broadband transducers for your ultimate fishing mission. Whether you’re a commercial fisherman, charter captain, or tournament angler, there’s a new game in town! Chirp transducers enable bottom detection down to 3,000m (10,000’) with 5 to 10 times greater detail and resolution so precise it’s possible to distinguish between individual baitfish, game fish, and underwater structures. One transducer delivers up to 80 kHz of total bandwidth in just one installation, saving customers time and money. Features:
|
B175M Bronze Thru Hull 20° Tilt - 1kW Rely on Airmar’s new broadband transducers for your ultimate fishing mission. Whether you’re a commercial fisherman, charter captain, or tournament angler, there’s a new game in town! Chirp transducers enable bottom detection down to 3,000m (10,000’) with 5 to 10 times greater detail and resolution so precise it’s possible to distinguish between individual baitfish, game fish, and underwater structures. One transducer delivers up to 80 kHz of total bandwidth in just one installation, saving customers time and money. Requires Mix and Match Cable Features:
|
B265LH Bronze Chirp Thru Hull 1kW with Fairing Block Requires Mix and Match Cable Imagine knowing what exact frequencies work the best at detecting specific fish species: Bluefin Tuna—60 kHz, Squid—133 kHz, and Cod—175 kHz. Now imagine tuning your fish finder to these frequencies, marking the fish precisely on the screen, then catching them! With the B265 transducer connected to a tunable fish finder, you too can have a log book like a commercial fisherman. This powerhouse transducer delivers extreme target detail, bottom discrimination, and bait and game fish separation at all depths. The B265LH is packed with a seven-element, low-frequency array that operates at anywhere between 42 kHz and 65 kHz. It has a wide, 25° beam that will adjust by several degrees as the frequency is tuned up or down the band. The single, high-frequency ceramic operates at any frequency between 130 kHz and 210 kHz and has a narrow, 6° beam that is adjustable by several degrees. The included High-Performance Fairing will give you broadband performance at speeds over 30 knots (34 MPH). We will leave it up to you to discover the rest of the secrets that can be unlocked with tunable, Chirp Broadband Transducer Technology. Features:
|
B275C-LHW Bronze Thru-Hull - Low & High Wide Frequency Requires Mix & Match Cable Get more coverage under the boat with Airmar's wide beam CHIRP product line. Offering a high frequency range of 150-250 kHz and a constant 25° beam width, these transducers are truly broadband at its best. In addition to improving the performance of CHIRP-ready echosounders, anglers using the new wide beam transducers will achieve twice the coverage under the boat compared to our current high frequency CHIRP transducers. A unique property of the high frequency transducers is that the beambwidth is a constant 25° angle across the entire frequency band. Now, in addition to providing vast bottom coverage and precise fish detection in the upper water column that can sometimes go unseen with our narrow beam transducers, Airmar's wide beam format also creates crisper and larger return images on the display. We've got you covered! Features:
|
B60 Bronze Thru-Hull Transducer w/Humminbird #9 Plug - 7-Pin - 20º The bronze B60-20º provides a vertical beam without a fairing. Inside the housing, the ceramic element is tilted for built-in, deadrise compensation. The resulting vertical beam gives excellent echo returns for more-accurate depth readings. The nearly-flush housing minimizes drag with only 5 mm (3/16") extending outside of the hull. Features:
Specifications:
|
B75H Bronze Chirp Thru Hull 20° Tilt - 600W Requires Mix and Match Cable Rely on Airmar’s broadband transducers for your ultimate fishing mission. Whether you’re a commercial fisherman, charter captain, or tournament angler, there’s a new game in town! Chirp transducers enable bottom detection down to 3,000m (10,000’) with 5 to 10 times greater detail and resolution so precise it’s possible to distinguish between individual baitfish, game fish, and underwater structures. One transducer delivers up to 80 kHz of total bandwidth in just one installation, saving customers time and money. Features:
|
B75HW High Wide Tilted Element Chirp Transducer - 20 Degree Deadrise, 600W Thru Hull Requires Mix and Match Cable for the appropriate Fishfinder it will be connected to. Airmar’s low-profile Chirp-ready transducer models are the perfect addition to smaller boats such as center consoles. The B75HW combines the benefits of the high-frequency band for amazing target separation on baitfish and schooling gamefish, with a wide 30° beamwidth for maximum coverage under the boat. The B75H transducer delivers up to 100 kHz of total bandwidth in just one installation and delivers amazing coverage under the boat in depths to 106 meters (350'). B75HW transmits across the following bandwidth: High frequency 150 to 250 kHz The transducer is installed almost flush to the hull. The tilt of the element corrects for the hull deadrise by orienting the beam directly down. This ensures maximum echo returns to the transducer for more accurate depth readings. Fixed 20° tilted version for 16° to 24° hull deadrise Features:
|
B75M Bronze Chirp Thru Hull 12° Tilt - 600W Requires Mix and Match Cable Rely on Airmar’s broadband transducers for your ultimate fishing mission. Whether you’re a commercial fisherman, charter captain, or tournament angler, there’s a new game in town! Chirp transducers enable bottom detection down to 3,000m (10,000’) with 5 to 10 times greater detail and resolution so precise it’s possible to distinguish between individual baitfish, game fish, and underwater structures. One transducer delivers up to 70 kHz of total bandwidth in just one installation, saving customers time and money. Features:
|
B75M Bronze Chirp Thru Hull 20° Tilt - 600W Requires Mix and Match Cable Rely on Airmar’s broadband transducers for your ultimate fishing mission. Whether you’re a commercial fisherman, charter captain, or tournament angler, there’s a new game in town! Chirp transducers enable bottom detection down to 3,000m (10,000’) with 5 to 10 times greater detail and resolution so precise it’s possible to distinguish between individual baitfish, game fish, and underwater structures. One transducer delivers up to 70 kHz of total bandwidth in just one installation, saving customers time and money. Features:
|
B765C-LM Bronze CHIRP Transducer - Needs Mix & Match Cable - Does NOT Work with Simrad & Lowrance Rely on Airmar’s broadband transducers for your ultimate fishing mission. Whether you’re a commercial fisherman, charter captain, or tournament angler, there’s a new game in town! Chirp transducers enable bottom detection down to 3,000m (10,000’) with 5 to 10 times greater detail and resolution so precise it’s possible to distinguish between individual baitfish, game fish, and underwater structures. One transducer delivers up to 85 kHz of total bandwidth in just one installation, saving customers time and money. A Thru-Hull Chirp transducer perfectly suited for smaller fishing boats, the B765L/M Chirps across the following bandwidths:*L/M -Low Frequency 40-75 kHz, Medium Frequency 80-130 kHz * Please Note: The low frequency operating band is 300 W. The medium frequency operating band is 600 W. Features
|
Deadrise Angle Finder - Accuracy of ± 1/2°
Accurate to 1/2 of 1°, this precision instrument, with strong ceramic magnet is designed for attachment to a carpenter's square or straight edge to overcome time consuming computation of angles. Features:
|
|
|
|
|
Copyright © 1999-2024 BuilderDepot, Inc. Site Designed and Maintained by Inline Internet Systems, Inc. |