This 45-degree elbow offsets obstructions as needed. Elbows swivel 360-degree at base. Angle not adjustable.
|
PelletVent Pro Collection 4 Inch Pellet Chimney Stainless Steel 90 Degree Elbow Warranty Notice: M&G DuraVent warranty applies to this professional grade product only when installed by a trained professional installer. This 4 Inch Pellet Chimney Stainless Steel 90 Degree Elbow from the PelletVent Pro series is a Type L Biofuel Chimney Pipe component and consists of the duralock system for a tight seal. Offsets obstructions as needed. Elbows swivel 360-¼ at base. Angle is not adjustable. Features: Fuel Type: BioFuel, Oil, Pellet Inner Diameter: 4" Elbow Angle: 90 Degrees Offsets Obstructions as Needed Double Wall Construction UL Listed All PelletVent Pro-+ components that come into contact with flue gases are built with an inner wall of corrosion resistant superferritic metal. PelletVent Pro is engineered with features for a durable, safe and aesthetically pleasing venting system. PelletVent Pro is a patent-pending venting system for stoves and inserts that use wood pellets, corn and other biofuels, or oil, as fuel. As a result of DuraVentG¬+s cutting-edge manufacturing process and commitment to innovation, PelletVent Pro is uncompromised in attention to detail and performance. This perfect fit and finish is made possible with a laser-welded inner and outer wall. Select components are available in black. PelletVent Pro is now UL listed for 1G¬- clearance to combustibles in the USA. ItG¬+s double-wall, air-insulated design offers superior performance. Seams are factory-sealed on all elbows, tees, and fittings. Since the introduction of pellet stoves in the 1980G¬+s, DuraVent is recognized as the industry leader in venting systems for pellet stoves. Looking for Simpson Dura-Vent? You found it! Simpson Dura-Vent has changed their name to DuraVent. DuraVent is a recognized technological leader in the venting industry
|
|
This chimney adaptor is used to transition between PelletVent Pro to existing chimney such as DuraTech, DuraPlus, or DuraTech Premium. Requires a DVL/DuraBlack Chimney Adaptor to fasten into support box or wall thimble.
|
This chimney adaptor is used to transition between PelletVent Pro to existing chimney such as DuraTech, DuraPlus, or DuraTech Premium. Requires a DVL/DuraBlack Chimney Adaptor to fasten into support box or wall thimble.
|
DuraVent Part Number: 4PVP-F6
4" Dura-Vent Pelletvent Pro Adjustable Flashing This item cannot ship to APO/FPO addresses. . M&G DuraVent provides no warranty for the following professional products if such products are not installed by a trained professional installer: DuraTech-+, DuraPlus HTC-+, DuraChimney-+ II, PelletVent Pro-+, DirectVent Pro-+, FasNSeal-+, FasNSeal-+ W2, FasNSeal-+ Flex, and PolyPro-+, and M&G DuraVent's relining products including DuraLiner-+, DuraFlex-+ (SW, Pro, 316, 304), and Ventinox-+. G¬= Any M&G DuraVent product sold by a non-approved website will not be warranted. G¬= Any customer that has bought product from a non-approved website will not be given technical assistance or support from M&G DuraVent. G¬= Any website not compliant with this Internet Sales Policy shall not use M&G DuraVent's trademarked and registered properties, and will be notified to remove them immediately. DuraVent reserves the right to enforce its intellectual property rights against entities not in compliance with this Internet Sales Policy. |
mfr: M&GDURAVENT DuraVent Part Number: 4PVP-WSA
4" Pelletvent Pro Wall Strap/tee Support, Adjustable This item cannot ship to APO/FPO addresses. Please accept our apologies. M&G DuraVent provides no warranty for the following professional products if such products are not installed by a trained professional installer: DuraTech-+, DuraPlus HTC-+, DuraChimney-+ II, PelletVent Pro-+, DirectVent Pro-+, FasNSeal-+, FasNSeal-+ W2, FasNSeal-+ Flex, and PolyPro-+, and M&G DuraVent's relining products including DuraLiner-+, DuraFlex-+ (SW, Pro, 316, 304), and Ventinox-+. G¬= Any M&G DuraVent product sold by a non-approved website will not be warranted. G¬= Any customer that has bought product from a non-approved website will not be given technical assistance or support from M&G DuraVent. G¬= Any website not compliant with this Internet Sales Policy shall not use M&G DuraVent's trademarked and registered properties, and will be notified to remove them immediately. DuraVent reserves the right to enforce its intellectual property rights against entities not in compliance with this Internet Sales Policy. |
This attic insulation shield is required for installations that pass through an attic to prevent insulation and debris from accumulating near the vent. Provides 1" clearance to combustibles.
|
This adaptor tee with clean-out cap is used for a 90-degree offset. Attaches directly to appliance as an adaptor. One piece unit incorporates removable twist-lock clean-out tee cap.
|
This appliance adaptor is used to connect PelletVent Pro to BioFlex when relining a masonry chimney. Only approved for use with BioFlex.
|
This clean-out tee cap is used as a replacement for your existing clean-out tee cap. The new PelletVent Pro tee Cap is a tight fit by design. We recommend using rubber gloves or a strap wrench to easily remove.
|
This double tee clean out tee cap allows clean-out access for horizontal and vertical installations. Use for a 90+ offset. Branch swivels for alignment. One piece unit incorporates removable twist-lock Clean-Out Tee Cap.
|
This increaser tee with clean-out cap attaches 3" pipe to branch and 4" pipe to body. Used for a 90-degree offset. Branch swivels for alignment. One piece unit incorporates removable twist-lock Clean-Out Tee Cap.
|
This single tee with clean-out cap is used for a 90-degree offset. Branch swivels for alignment. One piece unit incorporates removable twist-lock clean-out tee cap.
|
This cathedral ceiling support box is used to support pipe for both flat and cathedral ceilings. Trim and clamp included.
|
This firestop spacer is required where vent passes through ceiling and is used to reduce the chances of a fire. Centers pipe to provide proper 1" clearance to combustibles. Support clamp included.
|
This wall thimble is used for through-the-wall installations. Fits between standard wall studs. Comes with an insulation ring to reduce air infiltration where the pipe slips through the thimble.
|
This vertical cap is used for vertical installations only and helps protect your chimney liner from outside debris or water. Required where pipe terminates above the roof line.
|
This roof flashing is used with metal or tile roofs and helps provide an effective evacuation point for chimney exhaust while also keeping out debris and water . Made of dead soft aluminum.
|
This flex adaptor (female) is used to connect PelletVent Pro to BioFlex when relining a masonry chimney. Only approved for use with BioFlex.
|
This flex trim collar is used to connect PelletVent Pro rigid pipe to a masonry chimney with stainless steel flexible relining. Female end swivels to allow ease of connection.
|
This adaptor tee with clean-out cap is used for a 90-degree offset. Attaches directly to appliance as an adaptor. One piece unit incorporates removable twist-lock clean-out tee Cap.
|
This appliance adaptor is used to connect PelletVent Pro to BioFlex when relining a masonry chimney. Only approved for use with BioFlex.
|
This clean-out tee cap is used as a replacement for your existing clean-out tee cap. The new PelletVent Pro tee Cap is a tight fit by design. We recommend using rubber gloves or a strap wrench to easily remove.
|
This double tee clean out tee cap allows clean-out access for horizontal and vertical installations. Use for a 90-degree offset. Branch swivels for alignment. One piece unit incorporates removable twist-lock Clean-Out Tee Cap.
|
This increaser tee with clean-out cap attaches 3" pipe to branch and 4" pipe to body. Used for a 90-degree offset. Branch swivels for alignment. One piece unit incorporates removable twist-lock Clean-Out Tee Cap.
|
This single tee with clean-out cap is used for a 90-degree offset. Branch swivels for alignment. One piece unit incorporates removable twist-lock clean-out tee cap.
|
This tall cone roof flashing is used to weather-proof the penetration of vent pipe through the roof. Storm collar required. Select roof flashing based on pitch of roof. Use on flat roofs, chase enclosures, or masonry chimney.
|
This horizontal kit includes a horizontal cap to close off the pipe and prevent leaks or drips, wall thimble for passing pipe through a wall, and an appliance adaptor to form a solid connection to your appliance. Pipe lengths not included.
|
This house shield is used to protect exterior of structure from blower discharge in horizontal venting applications.
|
This flex adaptor (male) is used to connect PelletVent Pro to BioFlex when relining a masonry chimney. Only approved for use with BioFlex.
|
This quick release appliance adaptor is used to attach to appliance outlet allowing for easy pipe connection. It features an adjustable hose clamp and gasket to form a tight seal. The hose clamp can be loosened and tightened as needed to disconnect and connect the vent to the appliance.
|
|
|
|
|
Copyright © 1999-2024 BuilderDepot, Inc. Site Designed and Maintained by Inline Internet Systems, Inc. |