This anchor plate is used as a starter section for DuraChimney II. Bolts directly to the fireplace outlet.
|
This 30-degree elbow is used for offsets around obstructions such as rafters, ridgepoles, or joists.
|
This vertical chimney cap is required where pipe terminates above the roof line. It helps keep water and debris out of your chimney liner. Removable screws allow for cleaning of the chimney and spark arrestor screen.
|
This chimney pipe is designed for appliances that are tested and listed for use with a 2100-degreeF HT chimney system, such as wood stoves, fireplaces, furnaces, boilers, ranges, water heaters, or other appliances fueled by wood, oil, coal, or gas.
|
This chimney pipe is designed for appliances that are tested and listed for use with a 2100-degreeF HT chimney system, such as wood stoves, fireplaces, furnaces, boilers, ranges, water heaters, or other appliances fueled by wood, oil, coal, or gas.
|
This chimney pipe is designed for appliances that are tested and listed for use with a 2100-degreeF HT chimney system, such as wood stoves, fireplaces, furnaces, boilers, ranges, water heaters, or other appliances fueled by wood, oil, coal, or gas.
|
This chimney pipe is designed for appliances that are tested and listed for use with a 2100-degreeF HT chimney system, such as wood stoves, fireplaces, furnaces, boilers, ranges, water heaters, or other appliances fueled by wood, oil, coal, or gas.
|
This chimney pipe is an exceptional factory-built alternative to pre-fabricated masonry chimneys. DuraChimney II is a unitized, lightweight design which eliminates the need for field assembly of pipe sections, allowing for faster installation. Designed to stay cool on the outside, it also provides a hot draft on the inside and provides a fire-safe design that protects both the chimney and the building.
|
This chimney pipe is an exceptional factory-built alternative to pre-fabricated masonry chimneys. DuraChimney II is a unitized, lightweight design which eliminates the need for field assembly of pipe sections, allowing for faster installation. Designed to stay cool on the outside, it also provides a hot draft on the inside and provides a fire-safe design that protects both the chimney and the building.
|
This chimney pipe is an exceptional factory-built alternative to pre-fabricated masonry chimneys. DuraChimney II is a unitized, lightweight design which eliminates the need for field assembly of pipe sections, allowing for faster installation. Designed to stay cool on the outside, it also provides a hot draft on the inside and provides a fire-safe design that protects both the chimney and the building.
|
This chimney pipe is an exceptional factory-built alternative to pre-fabricated masonry chimneys. DuraChimney II is a unitized, lightweight design which eliminates the need for field assembly of pipe sections, allowing for faster installation. Designed to stay cool on the outside, it also provides a hot draft on the inside and provides a fire-safe design that protects both the chimney and the building.
|
This firestop is used in ceiling/floor penetrations above a fireplace to help reduce the chances of a fire. A firestop is not required when passing through the roof. Fits on the underside of ceiling.
|
This wall strap is used to support and to stabilize the chimney in interior or exterior installations to ensure a 2" clearance. Wall straps are required every 8' on exterior of the building only.
|
16" DuraChimney II Chimney Cap is used to terminate the chimney system. Required on all installations. Slides over the previous section of DuraChimney II pipe to allow for chimney height adjustment. Includes a Spark Arrestor.
|
This chimney pipe is designed for appliances that are tested and listed for use with a 2100-degreeF HT chimney system, such as wood stoves, fireplaces, furnaces, boilers, ranges, water heaters, or other appliances fueled by wood, oil, coal, or gas.
|
16" Duravent DuraTech Double-Wall Vertical Chimney Cap is required where pipe terminates above the roof line. Removable screws allow for cleaning of the chimney and spark arrestor screen. Made of stainless steel.
|
This ceiling support box supports chimney pipe and provides a positive connection between support box and chimney with a built-in twist lock. Suitable for both flat and cathedral (A-Frame) ceiling applications. Fits between standard 16" on-center joists and most manufactured home applications. Supports up to 60' of DuraTech Chimney. Use adaptor to attach DVL or DuraBlack to the support box. A 2" wide trim collar is included.
|
This ceiling support box supports chimney pipe and provides a positive connection between support box and chimney with a built-in twist lock. Suitable for both flat and cathedral (A-Frame) ceiling applications. Fits between standard 16ÿ on-center joists and most manufactured home applications. Supports up to 60' of DuraTech Chimney. Use adaptor to attach DVL or DuraBlack to the support box. A 2ÿ wide trim collar is included.
|
This square ceiling support box supports chimney pipe and provides a positive connection between support box and chimney with a built-in twist lock. Suitable for both flat and cathedral (A-Frame) ceiling applications. Fits between standard 16" on-center joists and most manufactured home applications. Supports up to 60' of DuraTech Chimney. Use adaptor to attach DVL or DuraBlack to the support box. A 2" wide trim collar is included.
|
This roof flashing is used to weatherproof the penetration of vent pipe through the roof. Storm Collar required. Select roof flashing based on pitch of roof. For pitches of 7/12 - 12/12. Made of galvalume.
|
3" DuraFlex All Fuel Component Kit includes: DuraFlex stainless steel top plate, DuraFlex stainless steel cap, and DuraFlex stainless steel tee. Flex lengths not included.
|
This flex connector is used to connect DuraFlex AL lengths to appliances, type B gas vents, or flex lengths.
|
DuraVent Part Number: 3DFS-MS
Dura-Vent 3" Mortar Sleeve for DuraFlex Light Liner system. 6" length, actual diameter is 1" larger than nominal. M&G DuraVent provides no warranty for the following professional products if such products are not installed by a trained professional installer: DuraTech-+, DuraPlus HTC-+, DuraChimney-+ II, PelletVent Pro-+, DirectVent Pro-+, FasNSeal-+, FasNSeal-+ W2, FasNSeal-+ Flex, and PolyPro-+, and M&G DuraVent's relining products including DuraLiner-+, DuraFlex-+ (SW, Pro, 316, 304), and Ventinox-+. G¬= Any M&G DuraVent product sold by a non-approved website will not be warranted. G¬= Any customer that has bought product from a non-approved website will not be given technical assistance or support from M&G DuraVent. G¬= Any website not compliant with this Internet Sales Policy shall not use M&G DuraVent's trademarked and registered properties, and will be notified to remove them immediately. DuraVent reserves the right to enforce its intellectual property rights against entities not in compliance with this Internet Sales Policy. |
3" DuraFlex Stainless Steel Connector Adaptor is used to connect DuraFlex SS length to an appliance, rigid length, or flex length. Drip-free connection.
|
3" DuraFlex Stainless Steel Rain Cap With Clamp Band is used to terminate a relining system at the top of the masonry chimney. Supports flex with a fast connect band.
|
mfr: M&GDURAVENT DuraVent Part Number: 3DFS-TP
Dura-Vent 3" CollarPlate with clamp band for DuraFlex Light Liner System. Supports the liner. Collar is 4" high. M&G DuraVent provides no warranty for the following professional products if such products are not installed by a trained professional installer: DuraTech-+, DuraPlus HTC-+, DuraChimney-+ II, PelletVent Pro-+, DirectVent Pro-+, FasNSeal-+, FasNSeal-+ W2, FasNSeal-+ Flex, and PolyPro-+, and M&G DuraVent's relining products including DuraLiner-+, DuraFlex-+ (SW, Pro, 316, 304), and Ventinox-+. G¬= Any M&G DuraVent product sold by a non-approved website will not be warranted. G¬= Any customer that has bought product from a non-approved website will not be given technical assistance or support from M&G DuraVent. G¬= Any website not compliant with this Internet Sales Policy shall not use M&G DuraVent's trademarked and registered properties, and will be notified to remove them immediately. DuraVent reserves the right to enforce its intellectual property rights against entities not in compliance with this Internet Sales Policy. |
The DuraVent PelletVent Pro 45Degree Elbow is for use to offset pipe diagonally or horizontally around obstructions. Elbow swivels a full 360Degree at the base, angle is not adjustable. PelletVent Pro is a venting system designed for stoves and inserts that use wood pellets and oil fuel. It is also built to vent corn and other biofuel products (Rated for continuous use flue temperatures up to 570Degree F). |
The Simpson PelletVent Pro 90Degree Elbow is for use to offset pipe diagonally or horizontally around obstructions. Elbow swivels a full 360Degree at the base, angle is not adjustable. PelletVent Pro is a venting system designed for stoves and inserts that use wood pellets and oil fuel. It is also built to vent corn and other biofuel products (Rated for continuous use flue temperatures up to 570Degree F). |
This 45-degree elbow offsets obstructions as needed. Elbows swivel 360-degree at base. Angle not adjustable.
|
This 90-degree elbow offsets obstructions as needed. Elbows swivel 360-degree at base. Angle not adjustable.
|
|
This cathedral ceiling support box is used to support pipe for both flat and cathedral ceilings. Trim and clamp included.
|
|
|
|
|
Copyright © 1999-2024 BuilderDepot, Inc. Site Designed and Maintained by Inline Internet Systems, Inc. |