This horizontal round cap is used for horizontal terminations only. The horizontal cap can be turned at the gore to direct exhaust output. Designed to create a venturi effect to force exhaust out. Made of a laser-welded, corrosion resistant stainless steel inner wall that is scientifically proven to resist corrosion from corn and other biofuels. Outer wall made of laser-welded stainless steel.
|
This storm collar is used to maintain a weather-tight resistant seal between the pipe and the flashing to keep out debris and water.
|
This cathedral ceiling vertical kit includes a vertical cap to provide a secure seal on a pipe, storm collar to prevent debris and water from entering the chimney liner, cathedral ceiling support box with trim and clamp, adjustable roof flashing, and appliance adaptor to connect to your appliance. Pipe lengths not included.
|
This vertical kit for flat ceilings includes a vertical cap for closing off the pipe with a tight seal, storm collar to keep water and debris from entering the liner, ceiling support firestop spacer to reduce the chances of a fire, adjustable flashing for your roof, and appliance adaptor to ensure a secure connection to your appliance. Also includes a 3" - 4" appliance adaptor/increaser and support clamp. Pipe lengths not included.
|
This wall thimble air intake kit allows outside fresh air for combustion through the wall thimble without having to cut a second hole into the wall. Comes with an insulation ring to reduce air infiltration where the pipe slips through the thimble. The 2" diameter flex hose is 10' in length. Clamps included. Can be used in US and Canada.
|
This vent increaser is used to increase the diameter of a vent.
|
mfr: M&GDURAVENT DuraVent Part Number: 0104S
4" To 6" Type B Vent Increaser This item cannot ship to APO/FPO addresses. Please accept our apologies. M&G DuraVent provides no warranty for the following professional products if such products are not installed by a trained professional installer: DuraTech-+, DuraPlus HTC-+, DuraChimney-+ II, PelletVent Pro-+, DirectVent Pro-+, FasNSeal-+, FasNSeal-+ W2, FasNSeal-+ Flex, and PolyPro-+, and M&G DuraVent's relining products including DuraLiner-+, DuraFlex-+ (SW, Pro, 316, 304), and Ventinox-+. G¬= Any M&G DuraVent product sold by a non-approved website will not be warranted. G¬= Any customer that has bought product from a non-approved website will not be given technical assistance or support from M&G DuraVent. G¬= Any website not compliant with this Internet Sales Policy shall not use M&G DuraVent's trademarked and registered properties, and will be notified to remove them immediately. DuraVent reserves the right to enforce its intellectual property rights against entities not in compliance with this Internet Sales Policy. |
This firestop spacer can help provide additional clearance from your venting to combustibles, ensuring better fire protection. Use at every ceiling level where Square Firestop Support is not used.
|
Use to connect appliance or single-wall connector to vent system. This product is manufactured by DURAVENT. This product is manufactured in United States.
|
This duracap is required where pipe terminates above the roof line. Use for vertical installations only.
|
This female adaptor is used to connect listed Type B Gas Vent system manufactured by other companies to existing Duravent Type B Gas Vent.
|
Use this roof flashing to weatherproof the penetration of vent pipe through the roof. Storm Collar required. Select roof flashing based on pitch of roof. For pitches of 0/12 - 6/12. Made of galvalume.
|
This roof flashing is used to weatherproof the penetration of vent pipe through the roof. Storm Collar required. Use on flat roofs, chase enclosures, or masonry chimney.
|
DuraVent Part Number: 131
4" Type B Vent High Wind Rain Cap This item cannot ship to APO/FPO addresses. . M&G DuraVent provides no warranty for the following professional products if such products are not installed by a trained professional installer: DuraTech-+, DuraPlus HTC-+, DuraChimney-+ II, PelletVent Pro-+, DirectVent Pro-+, FasNSeal-+, FasNSeal-+ W2, FasNSeal-+ Flex, and PolyPro-+, and M&G DuraVent's relining products including DuraLiner-+, DuraFlex-+ (SW, Pro, 316, 304), and Ventinox-+. G¬= Any M&G DuraVent product sold by a non-approved website will not be warranted. G¬= Any customer that has bought product from a non-approved website will not be given technical assistance or support from M&G DuraVent. G¬= Any website not compliant with this Internet Sales Policy shall not use M&G DuraVent's trademarked and registered properties, and will be notified to remove them immediately. DuraVent reserves the right to enforce its intellectual property rights against entities not in compliance with this Internet Sales Policy. |
This male adaptor is used to connect existing Duravent Type B Gas Vent to a listed Type B Gas Vent system manufactured by other companies. Male adaptor can also be used to attach to DuraFlex AL.
|
This storm collar is used to maintain a weather tight resistant seal between the pipe and the flashing.
|
This tee is used for a 90-degree offset or to combine connectors from two or more appliances into a common vent. Branch swivels for alignment. 3" - 8" feature swivel on male end.
|
This tee cap is used to cover standard tee or increaser tee. Remove tee cap to inspect the system; clean out debris or collected condensate from the common vent. Fits on inner liner.
|
This wall strap is used to provide support for offsets and horizontal runs. Recommended every 4¬ to support vertical common vent. Use also with DuraConnect or DuraConnect II. Wall Strap legs can be rotated 360 degrees to conceal screw.
|
DuraVent Part Number: 4PVP-12A
4" x 12" Pelletvent Pro Pipe, Adjusts 4"-10", 304-alloy Stainless Inner Pipe, Galvalume Outer This item cannot ship to APO/FPO addresses. . M&G DuraVent provides no warranty for the following professional products if such products are not installed by a trained professional installer: DuraTech-+, DuraPlus HTC-+, DuraChimney-+ II, PelletVent Pro-+, DirectVent Pro-+, FasNSeal-+, FasNSeal-+ W2, FasNSeal-+ Flex, and PolyPro-+, and M&G DuraVent's relining products including DuraLiner-+, DuraFlex-+ (SW, Pro, 316, 304), and Ventinox-+. G¬= Any M&G DuraVent product sold by a non-approved website will not be warranted. G¬= Any customer that has bought product from a non-approved website will not be given technical assistance or support from M&G DuraVent. G¬= Any website not compliant with this Internet Sales Policy shall not use M&G DuraVent's trademarked and registered properties, and will be notified to remove them immediately. DuraVent reserves the right to enforce its intellectual property rights against entities not in compliance with this Internet Sales Policy. |
This chimney pipe features fully unitized, twist-lock construction. Listed at 1" clearance to combustibles in the USA and Canada. It can be used in both vertical and horizontal installations. Stainless steel welded seam inner wall, combined with a galvalume welded seam outer wall. To calculate installed length, subtract 1 1/2" from each length of pipe.
|
This chimney pipe features fully unitized, twist-lock construction. Listed at 1" clearance to combustibles in the USA and Canada. It can be used in both vertical and horizontal installations. Stainless steel welded seam inner wall, combined with a galvalume welded seam outer wall. To calculate installed length, subtract 1 1/2" from each length of pipe.
|
This pipe extension is used to add 3" to 10" to rigid sections of pipe.
|
Use for venting listed natural gas or liquid propane Category I, draft hood appliances, or appliances that have been specifically tested and listed to use Type B Gas Vent. The appliances listed typically use Type B Gas Vent systems, but not always: Furnaces, Water Heaters, Boilers, Room Heaters, Decorative Gas Appliances, and Unit Heaters. To calculate installed length, subtract 1 1/2ÿ from each connection of vent. A 1ÿ clearance (air space) to combustible materials must be maintained. To calculate OD add 5/8ÿ.
|
4" X 15' DuraFlex 304-Alloy Stainless Steel Liner is used with wood-pellet, non-condensing gas, wood-burning, and oil appliances.
|
4" X 15' Duravent DuraFlex Stainless Steel Pre-Cut Light Liner can be used with wood-pellet, non-condensing gas, wood-burning, and oil appliances.
|
Use for venting listed natural gas or liquid propane Category I, draft hood appliances, or appliances that have been specifically tested and listed to use Type B Gas Vent. The appliances listed typically use Type B Gas Vent systems, but not always: Furnaces, Water Heaters, Boilers, Room Heaters, Decorative Gas Appliances, and Unit Heaters. To calculate installed length, subtract 1 1/2"from each connection of vent. A 1"clearance (air space) to combustible materials must be maintained. To calculate OD add 5/8.
|
4" X 20' Duravent DuraFlex 304-Alloy Stainless Steel Basic Liner Kit includes: DuraFlex SS Top Plate, DuraFlex SS Cap, DuraFlex SS Connector, and DuraFlex 304 length.
|
This connector pipe is used as a connector system to replace rigid gas vent with a flexible section. DuraConnect II can be used when Type B gas vent double-wall connector is required. Not to be enclosed and cannot penetrate through walls, floors, or ceilings. Twist-lock connectors on each end.
|
This chimney pipe features fully unitized, twist-lock construction. Listed at 1" clearance to combustibles in the USA and Canada. It can be used in both vertical and horizontal installations. Stainless steel welded seam inner wall, combined with a galvalume welded seam outer wall. To calculate installed length, subtract 1 1/2" from each length of pipe.
|
This chimney pipe features fully unitized, twist-lock construction. Listed at 1" clearance to combustibles in the USA and Canada. It can be used in both vertical and horizontal installations. Stainless steel welded seam inner wall, combined with a galvalume welded seam outer wall. To calculate installed length, subtract 1 1/2" from each length of pipe.
|
Use for venting listed natural gas or liquid propane Category I, draft hood appliances, or appliances that have been specifically tested and listed to use Type B Gas Vent. The appliances listed typically use Type B Gas Vent systems, but not always: Furnaces, Water Heaters, Boilers, Room Heaters, Decorative Gas Appliances, and Unit Heaters. To calculate installed length, subtract 1 1/2ÿ from each connection of vent. A 1ÿ clearance (air space) to combustible materials must be maintained. To calculate OD add 5/8ÿ.
|
|
|
|
|
Copyright © 1999-2024 BuilderDepot, Inc. Site Designed and Maintained by Inline Internet Systems, Inc. |