This wall strap is used in interior or exterior installations to add lateral support to the chimney. Assures a 2" clearance to combustible walls. Required every 4'.
|
This slip connector is used to adapt DuraBlack pipe to ceiling support box or finishing collar. Adds 3" - 13" of length to rigid pipe. Allows drip-free installation without cutting the pipe. Can be used in line to create a telescoping combination when used with a straight length of pipe. Requires screws.
|
This elbow offsets obstructions as needed. Elbows angles are now adjustable. Adjustable elbows are manufactured drip-free so creosote travels back to the stove as intended.
|
This trim collar is used as a decorative addition for DuraBlack connection to chimney to ensure a solid fit and an aesthetic appearance.
|
This 15-degree elbow offsets obstructions such as rafters, ridgepoles, or joists.
|
Use elbows to offset obstructions such as rafters, ridgepoles, or joists. 10"-16" II may have two pair of elbows, if needed. Offsets greater than 30-¼ are not allowed. Elbows are not adjustable.
|
This anchor plate is used as a starter section for DuraChimney II. Bolts directly to the fireplace outlet.
|
This chimney pipe is designed for appliances that are tested and listed for use with a 2100-degreeF HT chimney system, such as wood stoves, fireplaces, furnaces, boilers, ranges, water heaters, or other appliances fueled by wood, oil, coal, or gas.
|
This chimney pipe is designed for appliances that are tested and listed for use with a 2100-degreeF HT chimney system, such as wood stoves, fireplaces, furnaces, boilers, ranges, water heaters, or other appliances fueled by wood, oil, coal, or gas.
|
This chimney pipe is designed for appliances that are tested and listed for use with a 2100-degreeF HT chimney system, such as wood stoves, fireplaces, furnaces, boilers, ranges, water heaters, or other appliances fueled by wood, oil, coal, or gas.
|
DuraVent 99166 Class A Galvanized DuraTech Vent Pipe Elbow DuraTech Collection 10" Class A Double Wall Chimney Pipe Galvanized 30 Degree ElbowWarranty Notice: MandG DuraVent warranty applies to this professional grade product only when installed by a trained professional installer The DuraTech 10" Class A Double Wall Chimney Pipe Galvanized 30 Degree Elbow is used for offsets around obstructions such as rafters ridgepoles or joists May have one pairs of elbows if needed Offsets greater than 30 are not permitted in accordance to UL 103 standards Large diameters are restricted to one pair of elbows Inner wall is made of stainless steel and outer wall is galvalume Features:Angle: 30 Inner Diameter: 10"Outer Diameter: 12"UL ListedMaterial GalvanizedThe 30? elbow is sued for offsets around obstructions such as rafters ridgepoles or joists May have one pair of elbows if needed Offsets greater 30? are not permitted in accordance to UL 103 standards Large diameters are restricted to one par of elbows This elbow is fastened with screws Made of a galvalume outer wall and a stainless steel inner wall Looking for Simpson Dura Vent? You found it Simpson Dura Vent has changed their name to DuraVent DuraVent is a recognized technological leader in the venting industry Consistently the first to market with new innovations in venting systems DuraVent has captured a leadership position in emerging markets DuraVent has patents for several products and continues to design safe and technologically advanced venting The company s research into solving problems with corrosion when biofuels such as corn are used led to the break through patent for PelletVent Pro Scientifically proven materials and unequalled engineering make DuraVent products not only the best choice or safest choice but the only choice for professional quality venting products
|
This 30-degree elbow is used for offsets around obstructions such as rafters, ridgepoles, or joists.
|
This vertical chimney cap is required where pipe terminates above the roof line. It helps keep water and debris out of your chimney liner. Removable screws allow for cleaning of the chimney and spark arrestor screen.
|
This chimney pipe is designed for appliances that are tested and listed for use with a 2100-degreeF HT chimney system, such as wood stoves, fireplaces, furnaces, boilers, ranges, water heaters, or other appliances fueled by wood, oil, coal, or gas.
|
This chimney pipe is designed for appliances that are tested and listed for use with a 2100-degreeF HT chimney system, such as wood stoves, fireplaces, furnaces, boilers, ranges, water heaters, or other appliances fueled by wood, oil, coal, or gas.
|
This high-wind rain cap provides improved performance in high wind conditions. For vertical terminations only.
|
Use to maintain a weather tight resistant seal between the pipe and the flashing. This product is manufactured by Duravent. This product is manufactured in United States.
|
mfr: M&GDURAVENT DuraVent Part Number: 2012
10" x 12" Dura-black 24-ga Welded Black Stovepipe M&G DuraVent provides no warranty for the following professional products if such products are not installed by a trained professional installer: DuraTech-+, DuraPlus HTC-+, DuraChimney-+ II, PelletVent Pro-+, DirectVent Pro-+, FasNSeal-+, FasNSeal-+ W2, FasNSeal-+ Flex, and PolyPro-+, and M&G DuraVent's relining products including DuraLiner-+, DuraFlex-+ (SW, Pro, 316, 304), and Ventinox-+. G¬= Any M&G DuraVent product sold by a non-approved website will not be warranted. G¬= Any customer that has bought product from a non-approved website will not be given technical assistance or support from M&G DuraVent. G¬= Any website not compliant with this Internet Sales Policy shall not use M&G DuraVent's trademarked and registered properties, and will be notified to remove them immediately. DuraVent reserves the right to enforce its intellectual property rights against entities not in compliance with this Internet Sales Policy. |
Use for venting listed natural gas or liquid propane Category I, draft hood appliances, or appliances that have been specifically tested and listed to use Type B Gas Vent. The appliances listed typically use Type B Gas Vent systems, but not always: Furnaces, Water Heaters, Boilers, Room Heaters, Decorative Gas Appliances, and Unit Heaters. To calculate installed length, subtract 1 1/2"from each connection of vent. A 1"clearance (air space) to combustible materials must be maintained. To calculate OD add 5/8.
|
DuraVent Part Number: 2024
10" x 24" Dura-black 24-ga Welded Black Stovepipe M&G DuraVent provides no warranty for the following professional products if such products are not installed by a trained professional installer: DuraTech-+, DuraPlus HTC-+, DuraChimney-+ II, PelletVent Pro-+, DirectVent Pro-+, FasNSeal-+, FasNSeal-+ W2, FasNSeal-+ Flex, and PolyPro-+, and M&G DuraVent's relining products including DuraLiner-+, DuraFlex-+ (SW, Pro, 316, 304), and Ventinox-+. G¬= Any M&G DuraVent product sold by a non-approved website will not be warranted. G¬= Any customer that has bought product from a non-approved website will not be given technical assistance or support from M&G DuraVent. G¬= Any website not compliant with this Internet Sales Policy shall not use M&G DuraVent's trademarked and registered properties, and will be notified to remove them immediately. DuraVent reserves the right to enforce its intellectual property rights against entities not in compliance with this Internet Sales Policy. |
This chimney pipe is designed for appliances that are tested and listed for use with a 2100-degreeF HT chimney system, such as wood stoves, fireplaces, furnaces, boilers, ranges, water heaters, or other appliances fueled by wood, oil, coal, or gas.
|
This chimney pipe is an exceptional factory-built alternative to pre-fabricated masonry chimneys. DuraChimney II is a unitized, lightweight design which eliminates the need for field assembly of pipe sections, allowing for faster installation. Designed to stay cool on the outside, it also provides a hot draft on the inside and provides a fire-safe design that protects both the chimney and the building.
|
This chimney pipe is an exceptional factory-built alternative to pre-fabricated masonry chimneys. DuraChimney II is a unitized, lightweight design which eliminates the need for field assembly of pipe sections, allowing for faster installation. Designed to stay cool on the outside, it also provides a hot draft on the inside and provides a fire-safe design that protects both the chimney and the building.
|
This chimney pipe is an exceptional factory-built alternative to pre-fabricated masonry chimneys. DuraChimney II is a unitized, lightweight design which eliminates the need for field assembly of pipe sections, allowing for faster installation. Designed to stay cool on the outside, it also provides a hot draft on the inside and provides a fire-safe design that protects both the chimney and the building.
|
This chimney pipe is an exceptional factory-built alternative to pre-fabricated masonry chimneys. DuraChimney II is a unitized, lightweight design which eliminates the need for field assembly of pipe sections, allowing for faster installation. Designed to stay cool on the outside, it also provides a hot draft on the inside and provides a fire-safe design that protects both the chimney and the building.
|
This firestop is used in ceiling/floor penetrations above a fireplace to help reduce the chances of a fire. A firestop is not required when passing through the roof. Fits on the underside of ceiling.
|
This wall strap is used to support and to stabilize the chimney in interior or exterior installations to ensure a 2" clearance. Wall straps are required every 8' on exterior of the building only.
|
This square ceiling support box supports chimney pipe and provides a positive connection between support box and chimney with a built-in twist lock. Suitable for both flat and cathedral (A-Frame) ceiling applications. Fits between standard 16" on-center joists and most manufactured home applications. Supports up to 60' of DuraTech Chimney. Use adaptor to attach DVL or DuraBlack to the support box. A 2" wide trim collar is included.
|
This chase top flashing encloses the top of a chase while providing a ventilation air passage to the chase. Includes spacer clips.
|
This chimney cap is used to terminate the chimney system and to keep rain and debris out of your flue. Required on all installations. Slides over the previous section of DuraChimney II pipe to allow for chimney height adjustment. Includes a spark arrestor to prevent sparks from jumping out of flue.
|
This firestop is used in ceiling/floor penetrations above a fireplace to help reduce the chances of a fire. A firestop is not required when passing through the roof. Fits on the underside of ceiling.
|
Use to help prevent rain from entering the chase. Use with a flashing and a Chimney Cap. This product is manufactured by M&G DuraVent. This product is manufactured in United States.
|
|
|
|
|
Copyright © 1999-2024 BuilderDepot, Inc. Site Designed and Maintained by Inline Internet Systems, Inc. |