This pipe length is designed for appliances tested and listed for direct vent. Features a fully unitized twist-lock construction. Use of sealant is optional, unless specified by the appliance manufacturer. To calculate install length, subtract 1 1/2ÿ for each joint. No beads or hems. Black pipe lengths feature exterior laser-welded seams.
|
This pipe length is designed for appliances tested and listed for direct vent. Features a fully unitized twist-lock construction. Use of sealant is optional, unless specified by the appliance manufacturer. To calculate install length, subtract 1 1/2ÿ for each joint. No beads or hems.
|
This pipe length is designed for appliances tested and listed for direct vent. Features a fully unitized twist-lock construction. Use of sealant is optional, unless specified by the appliance manufacturer. To calculate install length, subtract 1 1/2ÿ for each joint. No beads or hems. Black pipe lengths feature exterior laser-welded seams.
|
This pipe length is designed for appliances tested and listed for direct vent. Features a fully unitized twist-lock construction. Use of sealant is optional, unless specified by the appliance manufacturer. To calculate install length, subtract 1 1/2ÿ for each joint. No beads or hems.
|
This elbow is used to offset obstructions as needed. Fully unitized, twist-lock construction. Elbows swivel, allowing the lock to remain fully engaged while aligning to the desired direction. The angle will remain fixed at 45-degree.
|
This pipe length is designed for appliances tested and listed for direct vent. Features a fully unitized twist-lock construction. Use of sealant is optional, unless specified by the appliance manufacturer. To calculate install length, subtract 1 1/2ÿ for each joint. No beads or hems. Black pipe lengths feature exterior laser-welded seams.
|
This pipe length is designed for appliances tested and listed for direct vent. Features a fully unitized twist-lock construction. Use of sealant is optional, unless specified by the appliance manufacturer. To calculate install length, subtract 1 1/2ÿ for each joint. No beads or hems.
|
This pipe length is designed for appliances tested and listed for direct vent. Features a fully unitized twist-lock construction. Use of sealant is optional, unless specified by the appliance manufacturer. To calculate install length, subtract 1 1/2ÿ for each joint. No beads or hems. Black pipe lengths feature exterior laser-welded seams.
|
This pipe length is designed for appliances tested and listed for direct vent. Features a fully unitized twist-lock construction. Use of sealant is optional, unless specified by the appliance manufacturer. To calculate install length, subtract 1 1/2ÿ for each joint. No beads or hems.
|
This pipe length is designed for appliances tested and listed for direct vent. Features a fully unitized twist-lock construction. Use of sealant is optional, unless specified by the appliance manufacturer. To calculate install length, subtract 1 1/2ÿ for each joint. No beads or hems. Black pipe lengths feature exterior laser-welded seams.
|
This pipe length is designed for appliances tested and listed for direct vent. Features a fully unitized twist-lock construction. Use of sealant is optional, unless specified by the appliance manufacturer. To calculate install length, subtract 1 1/2ÿ for each joint. No beads or hems.
|
This roof flashing is used to weather-proof the penetration of vent pipe through the roof. Storm collar required.
|
This pipe length is designed for appliances tested and listed for direct vent. Features a fully unitized twist-lock construction. Use of sealant is optional, unless specified by the appliance manufacturer. To calculate install length, subtract 1 1/2ÿ for each joint. No beads or hems.
|
This elbow is used to offset obstructions as needed. Fully unitized, twist-lock construction. Elbows swivel, allowing the lock to remain fully engaged while aligning to the desired direction. The angle will remain fixed at 90-degree.
|
This elbow is used to offset obstructions as needed. Fully unitized, twist-lock construction. Elbows swivel, allowing the lock to remain fully engaged while aligning to the desired direction. The angle will remain fixed at 90-degree.
|
This attic insulation shield is required for installations that pass through an attic to prevent insulation and debris from accumulating near the vent. Provides 1" clearance to combustibles. Includes base with tube, extension tube and collar.
|
This support box is used to pass through ceiling and support pipe. May be used on vaulted or flat ceilings. Trim and clamp included.
|
This ceiling support/wall thimble cover is used as a decorative cover for horizontal (through-wall) installations or for flat ceiling installations. Fits over the wall thimble face plate. Comes with an insulation ring to reduce air infiltration where the pipe slips through the thimble.
|
This roof flashing is used to weather-proof the penetration of vent pipe through the roof. Storm collar required. Used for metal or tile roofs.
|
This square horizontal high Wind Termination Cap is used for standard and high-wind through-the-wall termination. Check installation instructions for restrictions on horizontal cap terminations, such as minimum distance from windows and doors.
|
This siding standoff is used as a heat shield on structures with vinyl siding, or other temperature sensitive materials, to help prevent warping and/or melting of the material. Use only on horizontal terminations and on any irregular surfaced siding (i.e.: ship lap siding, shake shingle siding) so cap is not imbedded in the siding. Sized for Square Horizontal Cap.
|
This snorkel termination cap is used for horizontal through-the-wall termination when a vertical rise is desired in the system to meet appliance manufacturer recommended minimum heights. Do not enclose in the wall or install below grade.
|
This wall firestop is designed for horizontal (through-wall) installations to help reduce chances of a fire. Refer to the appliance manufacturer's installation instructions for requirements.
|
This wall strap is used to support vent pipe. Provides 1" clearance. Recommend installing Wall Straps at 4-foot intervals on vertical runs.
|
This wall thimble provides a complete wall-pass-through and firestop. Use with square horizontal cap only. May be required in Canada. Refer to the appliance manufacturer's installation instructions for requirements.
|
This adjustable pipe adds length to your DirectVent pipe. Use of sealant is optional, unless specified by the appliance manufacturer.
|
This adjustable pipe adds length to your DirectVent pipe. Use of sealant is optional, unless specified by the appliance manufacturer.
|
This ceiling firestop is required for multi-story vertical installations at the second floor and any subsequent floors, and it can help reduce chances of a fire.
|
This elbow is used to offset obstructions as needed. Fully unitized, twist-lock construction. Elbows swivel, allowing the lock to remain fully engaged while aligning to the desired direction. The angle will remain fixed at 45-degree.
|
This vertical high wind termination cap is used for standard and high-wind through-the-wall termination. Check installation instructions for restrictions on horizontal cap terminations, such as minimum distance from windows and doors.
|
Use for supporting vent pipe between offsets. This product is manufactured by Duravent. This product is manufactured in United States.
|
This storm collar is used to maintain a weather-tight resistant seal between the pipe and the flashing and to keep debris and water out of your chimney liner.
|
|
|
|
|
Copyright © 1999-2024 BuilderDepot, Inc. Site Designed and Maintained by Inline Internet Systems, Inc. |